1998-2002 ISUZU EXP UBS WORKSHOP MANUAL – PDF DOWNLOAD

1998-2002 ISUZU EXP UBS WORKSHOP MANUAL – PDF DOWNLOAD

IMAGE PREVIEW:

1998-2002 ISUZU EXP UBS WORKSHOP MANUAL

1998-2002 ISUZU EXP UBS WORKSHOP MANUAL

DESCRIPTION:

1998-2002 ISUZU EXP UBS WORKSHOP MANUAL – PDF DOWNLOAD

• Park the vehicle on level ground and chock the front or rear wheels before lifting the vehicle. 2. Use covers on the vehicle body, seats, and floor to prevent damage and/or contaminations.
• 3. Disconnect the grounding cable from the battery before performing service operations. This will prevent cable damage or burning due to shortcircuiting. 4. Raise the vehicle with a jack set against the recommended lifting points (see “Lifting instructions” in this section). 5. Support the vehicle on chassis stands.
• 6. Handle brake fluid and antifreeze solution with great care. Spilling these liquids on painted surfaces will damage the paint. 7. The use of the proper tool(s) and special tool(s) where specified is essential to efficient, reliable, and safe service operations. 8. Always use genuine ISUZU replacement parts. 9. Discard used cotter pins, gasket, plastic clips, O-rings, oil seals, lock washers, and selflocking nuts at disassembly.
• Normal function of these parts cannot be guaranteed if they are reused. 10. Keep the disassembled parts neatly in groups. This will facilitate smooth and correct reassembly. 11. Keep fixing nuts and bolts separate. Fixing nuts and bolts vary in hardness and design according to installation positions. 12. Clean all parts before inspection or reassembly. 1
• 3. Clean the oil ports and other openings with compressed air to make certain that they are free of dirt and obstructions. 14. Lubricate the rotating and sliding faces of all moving parts with oil or grease before installation. 15. Use the recommended liquid gasket to prevent leakage. 16. Carefully observe all nut and bolt torque specifications.
• 17. When service operation is completed, make a final check to be sure service has been done properly and problem has been corrected. 18. When removing or replacing parts that require refrigerant to be discharged from the air conditioning system, be sure to use the following tools to recover and recycle the Refrigerant-134a (R-134a). For 134a: Use the R-134a Refrigerant Recovery/Recovery/ Recycling/Recharging/System (ACR4) or its equivalent to prevent the discharge of refrigerant into the air.

TABLE OF CONTENTS:

1998-2002 ISUZU EXP UBS WORKSHOP MANUAL – PDF DOWNLOAD

General Repair Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A– 2
How To Use This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A– 3
Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A– 6
Lifting Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A– 8
Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A–10
Recommended Liquid Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A–11
Recommended Thread Locking Agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A–11
Abbreviations Charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0A–12