Fassi Crane F410A.23 Use and Maintenance Manual  – PDF DOWNLOAD

Fassi Crane F410A.23 Use and Maintenance Manual  – PDF DOWNLOAD

FILE DETAILS:

Fassi Crane F410A.23 Use and Maintenance Manual  – PDF DOWNLOAD

Language : English
Pages :92
Downloadable : Yes
File Type : PDF

TABLE OF CONTENTS:

Fassi Crane F410A.23 Use and Maintenance Manual  – PDF DOWNLOAD

INDEX
1 INTRODUCTION
2 CLASSIFICATION OF THE CRANE MODEL
2.1 Generality
2.2 Hydraulic jibs
2.3 Technical data
3 CAPACITY PLATES
3.1 Generality
3.1.1 Capacity plates with lifting moment limiting device
4 HYDRAULIC SCHEMATICS (version with lifting moment limiting device)
5 ELECTRIC SCHEMATICS
6 SAFETY NORMS
7 WARNING AND INSTRUCTIONS
7.1 Generality
7.2 Before operating
7.3 During operation
7.4 At the end of the operation (Prior to driving the vehicle)
7.5 Residual risks
8 IDENTIFICATION OF THE CRANE MODEL
8.1 Generality
8.2 Crane mark
9 CRANE NOMENCLATURE
9.1 Crane with ground controls on both sides
9.2 Crane with top seat controls and with ground controls for outriggers
10 NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES
10.1 Crane with ground controls on both sides
10.2 Crane with top seat controls and with ground controls for outriggers
11 SUPPLEMENTARY BEAMS
11.1 Generality
11.2 Identification of the supplementary beams
12 TILTABLE OUTRIGGER RAMS
12.1 Manually tiltable outrigger rams
13 MANOEUVRES AND CONTROLS TO STABILIZE THE VEHICLE
13.1 Generality
13.2 Manual extension and re-entry of the outrigger supports (not available)
13.3 Manoeuvres for the manual extension of the double outrigger supports (not available)
13.4 Functions of control levers for stabilization
13.5 Controls to stabilize the vehicle
13.5.1 Crane with hydraulic tiltable supports (with RACK) for outrigger rams
Edition 25.05.2005
14 CONTROLS TO OPERATE THE CRANE
14.1 Generality
14.2 Manoeuvres to unfold the crane into a working condition
14.3 Manoeuvres to fold the crane into the rest condition
14.4 Manoeuvres to unfold the crane “C” into a working condition (only for the crane version “C”)
14.5 Manoeuvres to fold the crane “C” into the rest condition (only for the crane version “C”)
14.6 Indicator of inner boom horizontal position (optional)
14.7 Third control station (optional)
15 MANOEUVRES OF THE CRANE LOADS (version with load limiting device)(not available)
16 MANOEUVRES OF THE CRANE LOADS (version with lifting moment limiting device)
16.1 Generality
16.2 Lifting moment limiting device “ELECTRONIC”
16.3 Control panels
16.4 Load handling
16.5 Lifting moment limiting device for two working sectors
16.6 Rotation limiting device
16.7 In the case of the appearance of the signal “ALARM” on the display of the control
panel or of the radio remote control or in case of an electrical failure
16.7.1 Diagnostic (Alarms/Input/Output) LME vers. 4-5 UC 01-7
16.7.2 Temporary OVERIDE-Reactivation for the crane functions with standard distributor
16.7.3 OVERIDE-Reactivation lever for the crane functions (with Danfoss distributor)
16.8 XP device (if fitted, see the Use and Maintenance booklet)
16.8.1 Activation and instructions for use of the XP/V device
(if fitted, see the Use and Maintenance booklet)
16.9 Use of the radio remote control (if fitted)
16.9.1 Scanreco control unit with linear levers (if fitted)
17 USE OF IMPLEMENTS
17.1 Generality
17.2 Hydraulic connections for implements – supplementary hoses
17.3 Oil cooler (heat exchanger)
18 MANUAL EXTENSIONS
18.1 Generality
18.2 Lifting moment limiting device “ELECTRONIC” for the manual extensions
(valid starting from the version 3.0 of the software)
19 CONTROLS TO OPERATE THE HYDRAULIC IMPLEMENTS OF THE CRANE
20 HYDRAULIC JIBS
20.1 Generality
20.2 Identification of the hydraulic jib
20.3 Nomenclature of the hydraulic jib
20.4 Manoeuvres to unfold the jib in working condition
20.5 Manoeuvres to fold the jib in rest condition
20.6 Operations to remove the hydraulic jib from the crane
20.7 Operations to mount the hydraulic jib on the crane
20.8 Hydraulic jib articulated at 25 degrees with the automatic control (L515-L516)(not available)
20.9 Use of the hydraulic jib articulated at 25 degrees (not available on the L102 and on the L515-L516)
20.10 Crane with lifting moment limiting device and “pro link” (if fitted)
21 WINCH (if fitted)
21.1 Generality (version with lifting moment limiting device)
21.2 Winch for crane (version with lifting moment limiting device)
21.2.1 Winches equipped with a mechanical stroke end device
22 MAINTENANCE INSTRUCTIONS
22.1 Generality
22.2 Timer
22.3 After every 8 working hours or at the end of every working day
22.4 After every 40 working hours or atfter every working week
22.5 After every 100 working hours or more frequently in case of more intensive utilisation
22.6 After every 500 working hours or after every 6 working months
22.7 After every 1000 working hours or after every working year
22.8 Complete overhaul of the crane is required when 10.000 working hours or 10 years’
life are reached
22.9 Instructions for the dismantlement and the demolition of a FASSI crane
23 TABLE OF HYDRAULIC OIL AND LUBRICANTS CHARACTERISTICS
24 POSSIBLE FAULTS
24.1 Generality
24.2 Only operations which can be carried out by the user
24.3 Operations to be carried out only by a service center
25 INSTRUCTION AND WARNING PLATES

IMAGES PREVIEW OF THE MANUAL: