Fassi Cranes F 700A/800AXP.26 use and maintenance Manual SN 1001 – PDF DOWNLOAD

Fassi Cranes F 700A/800AXP.26 use and maintenance Manual SN 1001 – PDF DOWNLOAD

FILE DETAILS:

Fassi Cranes F 700A/800AXP.26 use and maintenance Manual SN 1001 – PDF DOWNLOAD

Language : English
Pages :102
Downloadable : Yes
File Type : PDF

TABLE OF CONTENTS:

Fassi Cranes F 700A/800AXP.26 use and maintenance Manual SN 1001 – PDF DOWNLOAD

INDEX
1 INTRODUCTION
2 CLASSIFICATION OF THE CRANE MODEL
2.1 Generality
2.2 Hydraulic jibs
2.3 Technical data
3 CAPACITY PLATES
3.1 Generality
3.1.1 Capacity plates with lifting moment limiting device
4 HYDRAULIC SCHEMATICS
5 ELECTRIC SCHEMATICS
6 SAFETY NORMS
7 WARNING AND INSTRUCTIONS
7.1 Generality
7.2 Before operating
7.3 During operation
7.4 At the end of the operation (Prior to driving the vehicle)
7.5 Residual risks
8 IDENTIFICATION OF THE CRANE MODEL
8.1 Generality
8.2 Crane mark
9 CRANE NOMENCLATURE
9.1 Controls for crane and outriggers through push-button panel of the radio remote control
10 NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES
10.1 Controls for crane and outriggers through push-button panel of the radio remote control
11 SUPPLEMENTARY BEAMS
11.1 Generality
11.2 Identification of the supplementary beams
12 TILTABLE OUTRIGGER RAMS
12.1 Manually tiltable outrigger rams
13 MANOEUVRES AND CONTROLS TO STABILIZE THE VEHICLE
13.1 Generality
13.2 Functions of control levers for stabilization
13.3 Controls to stabilize the vehicle
13.3.1 Crane with fixed or manually tiltable supports for outrigger rams
13.3.2 Crane with hydraulic tiltable supports (WITH CHAIN) for outrigger rams
Edition 22.07.2005
14 CONTROLS TO OPERATE THE CRANE
14.1 Generality
14.2 Manoeuvres to unfold the crane into a working condition
14.3 Manoeuvres to fold the crane into the rest condition
15 MANOEUVRES OF THE CRANE LOADS (version with load limiting device) (not available)
16 MANOEUVRES OF THE CRANE LOADS (version with lifting moment limiting device)
16.1 Generality
16.2 Lifting moment limiting device “ELECTRONIC”
16.3 Control panel
16.4 Load handling
16.5 Lifting moment limiting device for two working sectors
16.6 Rotation limiting device
16.7 In the case of the appearance of the signal “ALARM” on the display of the control panel or of
the radio remote control or in case of an electrical failure
16.7.1 Diagnostic (Alarms/Input/Output) LME vers. 4-5 UC 01-7
16.7.2 Temporary OVERIDE-Reactivation for the crane functions in case of the appearance of the
signal “ALARM” on the display of the push-button panel
16.7.3 Temporary OVERIDE-Reactivation for the crane functions in case of an electrical failure, out
of order of the radio remote control, or of the appearance of the signal “ALARM” on the
display of the push-button panel (in this case, we cannot reactivate the crane functions)
16.8 XP device (if fitted, see the Use and Maintenance booklet)
16.8.1 Activation and instructions for use of the XP/V device
(if fitted, see the Use and Maintenance booklet)
16.9 IMC and ADC devices (if fitted, see the Use and Maintenance booklet)
17 USE OF IMPLEMENTS
17.1 Generality
17.2 Hydraulic connections for implements – supplementary hoses
17.3 Oil cooler (heat exchanger)
18 MANUAL EXTENSIONS
18.1 Generality
18.2 Lifting moment limiting device “ELECTRONIC” for the manual extensions
(valid starting from the version 3.0 of the software) (if fitted)
19 CONTROLS TO OPERATE THE HYDRAULIC IMPLEMENTS OF THE CRANE (not available)
20 HYDRAULIC JIBS
20.1 Generality
20.2 Identification of the hydraulic jib
20.3 Nomenclature of the hydraulic jib
20.4 Manoeuvres to unfold the jib in working condition
20.5 Manoeuvres to fold the jib in rest condition
20.6 Operations to remove the hydraulic jib from the crane
20.7 Operations to mount the hydraulic jib on the crane
20.8 Hydraulic jib articulated at 25 degrees with the automatic control (L515-L516)
20.9 Use of the hydraulic jib articulated at 25 degrees (not available on the L102 and on the L515-L516)
20.10 Crane with lifting moment limiting device and “pro link” (if fitted)
21 WINCH (if fitted)
21.1 Generality
21.2 Winch for crane
21.2.1 Winches equipped with a mechanical stroke end device
22 MAINTENANCE INSTRUCTIONS
22.1 Generality
22.2 Timer
22.3 After every 8 working hours or at the end of every working day
22.4 After every 40 working hours or atfter every working week
22.5 After every 100 working hours or more frequently in case of more intensive utilisation
22.6 After every 500 working hours or after every 6 working months
22.7 After every 1000 working hours or after every working year
22.8 Complete overhaul of the crane is required when 10.000 working hours or 10 years’life
are reached
22.9 Instructions for the dismantlement and the demolition of a FASSI crane
23 TABLE OF HYDRAULIC OIL AND LUBRICANTS CHARACTERISTICS
24 POSSIBLE FAULTS
24.1 Generality
24.2 Only operations which can be carried out by the user
24.3 Operations to be carried out only by a service center
25 INSTRUCTION AND WARNING PLATES
1

IMAGES PREVIEW OF THE MANUAL: