Fassi Cranes F 80A.23 Use and Maintenance Manual SN 4085 – PDF DOWNLOAD

Fassi Cranes F 80A.23 Use and Maintenance Manual SN 4085 – PDF DOWNLOAD

FILE DETAILS:

Fassi Cranes F 80A.23 Use and Maintenance Manual SN 4085 – PDF DOWNLOAD

Language : English
Pages :94
Downloadable : Yes
File Type : PDF

TABLE OF CONTENTS:

Fassi Cranes F 80A.23 Use and Maintenance Manual SN 4085 – PDF DOWNLOAD

INDEX
1 INTRODUCTION
2 CLASSIFICATION OF THE CRANE MODEL
2.1 Generality
2.2 Hydraulic jibs (not available)
2.3 Technical data
3 CAPACITY PLATES
3.1 Generality
3.1.1 Capacity plates with lifting moment limiting device
3.1.2 Capacity plates with load limiting device
4 HYDRAULIC SCHEMATICS ( ) (version with lifting moment limiting device)
4.1 HYDRAULIC SCHEMATICS (version with load limiting device)
5 ELECTRIC SCHEMATICS
6 SAFETY NORMS
7 WARNING AND INSTRUCTIONS
7.1 Generality
7.2 Before operating
7.3 During operation
7.4 At the end of the operation (Prior to driving the vehicle)
7.5 Residual risks
8 IDENTIFICATION OF THE CRANE MODEL
8.1 Generality
8.2 Crane mark
9 CRANE NOMENCLATURE
9.1 Crane with ground controls on both sides
Crane with ground controls on both sides and with top seat controls by hand cables
9.2 Crane with top seat controls and with ground controls for outriggers
10 NOMENCLATURE OF THE SAFETY AND PROTECTION DEVICES
10.1 Crane with ground controls on both sides
Crane with ground controls on both sides and with top seat controls by hand cables
10.2 Crane with top seat controls and with ground controls for outriggers
11 SUPPLEMENTARY BEAMS
11.1 Generality
11.2 Identification of the supplementary beams
12 TILTABLE OUTRIGGER RAMS
12.1 Manually tiltable outrigger rams
13 MANOEUVRES AND CONTROLS TO STABILIZE THE VEHICLE
13.1 Generality
Edition ExtraCE 01.04.2005
13.2 Manual extension and re-entry of the outrigger supports
13.3 Manoeuvres for the manual extension of the double outrigger supports
13.4 Functions of control levers for stabilization
13.5 Controls to stabilize the vehicle
14 CONTROLS TO OPERATE THE CRANE
14.1 Generality
14.2 Manoeuvres to unfold the crane into a working condition
14.3 Manoeuvres to fold the crane into the rest condition
14.4 Manoeuvres to unfold the crane “C” into a working condition (only for the crane version “C”)
14.5 Manoeuvres to fold the crane “C” into the rest condition (only for the crane version “C”)
14.6 Indicator of inner boom horizontal position (optional)
14.7 Third control station (optional)
15 MANOEUVRES OF THE CRANE LOADS (version with load limiting device)
Generality
16 MANOEUVRES OF THE CRANE LOADS (version with lifting moment limiting device)(optional)
16.1 Generality
16.2 Lifting moment limiting device “ELECTRONIC” (optional)
16.3 Control panels (optional)
16.4 Load handling (optional)
16.5 Lifting moment limiting device for two working sectors (optional)
16.6 Rotation limiting device (optional)
16.7 In the case of the appearance of the signal “ALARM” on the display of the control
panel or of the radio remote control or in case of an electrical failure (optional)
16.7.1 Diagnostic (Alarms/Input/Output) LME vers. 4-5 UC 01-7 (optional)
16.7.2 Temporary OVERIDE-Reactivation for the crane functions with standard distributor (optional)
16.7.3 OVERIDE-Reactivation lever for the crane functions (with Danfoss distributor) (optional)
16.8 XP device (if fitted, see the Use and Maintenance booklet)
16.8.1 Activation and instructions for use of the XP/V device (if fitted, see the Use and Maintenance booklet)
17 USE OF IMPLEMENTS
17.1 Generality
17.2 Hydraulic connections for implements – supplementary hoses
17.3 Oil cooler (heat exchanger)
18 MANUAL EXTENSIONS
18.1 Generality
18.2 Lifting moment limiting device “ELECTRONIC” for the manual extensions
(valid starting from the version 3.0 of the software)
19 CONTROLS TO OPERATE THE HYDRAULIC IMPLEMENTS OF THE CRANE
20 HYDRAULIC JIBS (not available)
21 WINCH (if fitted)
21.1 Generality (version with lifting moment limiting device) (optional)
21.2 Winch for crane
21.2.1 Winches equipped with a mechanical stroke end device
21.3 Generality (version with load limiting device)
21.4 Winch for crane
21.4.1 Winches equipped with a mechanical stroke end device
22 MAINTENANCE INSTRUCTIONS
22.1 Generality
22.2 Timer
22.3 After every 8 working hours or at the end of every working day
22.4 After every 40 working hours or atfter every working week
22.5 After every 100 working hours or more frequently in case of more intensive utilisation
22.6 After every 500 working hours or after every 6 working months
22.7 After every 1000 working hours or after every working year
22.8 Complete overhaul of the crane is required when 10.000 working hours or 10 years’life are reached
22.9 Instructions for the dismantlement and the demolition of a FASSI crane
23 TABLE OF HYDRAULIC OIL AND LUBRICANTS CHARACTERISTICS
24 POSSIBLE FAULTS
24.1 Generality
24.2 Only operations which can be carried out by the user
24.3 Operations to be carried out only by a service center
25 INSTRUCTION AND WARNING PLATES

IMAGES PREVIEW OF THE MANUAL: