Gehl Manure Spreaders Mechanical & Hydraulic Drive 1410 Parts Manual(908045B) – PDF DOWNLOAD

Gehl Manure Spreaders Mechanical & Hydraulic Drive 1410 Parts Manual(908045B) – PDF DOWNLOAD

TABLE OF CONTENTS:

Gehl Manure Spreaders Mechanical & Hydraulic Drive 1410 Parts Manual(908045B) – PDF DOWNLOAD

Introduction Inside Front Cover
Table of Contents 1
Decal Locations 2-3
PTO 4-5
Hitch Frame & Jack 6-7
Main Frame, Floor, Axle Beam & Hub Assembly 8-9
Single Apron & Apron Chains 10-11
Double Apron Shafts 12-13
Apron Controls 14-15
Apron Control Hydraulic Cylinder 16-17
Front Drive 18-19
Apron & Beater Drive (Mechanical Drive) 20-23
Beater Drive Gearbox 24-25
Apron Drive Gearbox (Mechanical Drive) 26-27
Hydraulic Apron Drive – Flow Control Valve 28-29
Hydraulic Apron Drive – Rear Drive 30-31
Hydraulic Drive Motor 32-33
Flow Control Valve 34-35
Apron Drive Gearbox (Hydraulic Drive) 36-37
Front Endgate 38-39
Front & Side Shields 40-41
Side Sheets & Rear Supports 42-43
Beater 44-45
Upper Beater 46-47
Litter Pan 48-49
Hydraulic Endgate 50-51
Endgate Hydraulic Cylinder 52-53
Options & Accessories 54-58
Transport Lights 54-57
Safety Chain 58
Alphabetical Index 59
Numerical Index 60-67
Hydraulic Fitting Torque Data 68
Standard Hardware Torque Specifications Inside Back Cover

DESCRIPTION:

Gehl Manure Spreaders Mechanical & Hydraulic Drive 1410 Parts Manual(908045B) – PDF DOWNLOAD

Introduction:

• When ordering service parts, please specify the correct part number, full description, quantity required, unit model number, and serial number. For your safety and continued proper operation, only use genuine GEHL service parts.
• The Manure Spreader model and serial numbers for this unit are located on a decal on the left side of the main frame at the front left corner of the box. Please note that “right” and “left” are determined from a position standing behind the Manure Spreader.
• GEHL Company reserves the right to make changes or improvements to the design or construction of any part of the unit without incurring the obligation to install such changes on any previously delivered units.
• Please refer to the abbreviations table located on this page for the various fastener descriptions. Standard attaching hardware torque values are provided on the inside back cover.
• In the exploded view parts list, Reference Numbers may have additional information following the Reference Number. A tear drop symbol indicates an application of a “wet” product such as oil, and the number inside the tear drop will correspond to the description in the Parts List. A number inside a hexagon will be the torque value required, in foot-pounds, on the associated Reference Number. Items shown in the parts list that do not have Reference Numbers are shown for reference purposes only and are NOT available for purchase.
• Unless otherwise specified, all cap screws or bolts are Grade 5, zinc-plated. Hexagon nuts for Grade 5 cap screws or bolts are Grade B, while hexagon nuts for other cap screws or bolts are Grade A.

GENERAL INFORMATION:

• Decal location information is provided to assist in the proper selection and application of new decals, in the event the original decals become damaged or the machine is repainted. Please refer to the listing for the illustration reference number, part number, description, and quantity of each decal provided in the kit. Refer to the appropriate illustrations for replacement locations.
• To ensure proper selection for correct replacement decals, compare all of the various close-up location illustrations of the machine BEFORE starting to refinish the unit. Then, circle each pictured decal applicable to your machine, while checking off its part number in the listing. After verifying all the decals needed for replacement, set aside any unneeded decals for disposal.

IMAGES PREVIEW OF THE MANUAL: