GEHL Skid Loader 4615 Service Parts Manual(904592) – PDF DOWNLOAD

GEHL Skid Loader 4615 Service Parts Manual(904592) – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

  
DESCRIPTION:

GEHL Skid Loader 4615 Service Parts Manual(904592) – PDF DOWNLOAD

Introduction:

• When ordering service parts, specify the correct part number, full description, quantity required, and the unit model and serial numbers. Model and serial num­ bers for this unit are on a Decal located inside the Right Chassis Riser, between the Lift Arm and Lift Cylinder.
• “Right” and “Left” are determined from a position sitting on the Seat and facing forward. From this posi­ tion, the Propulsion Control T-bar is on the left and the Lift/Tilt Control T-bar is on the right. GEHL® Company reserves the right to make changes or improvements in the design or construction of any part of the unit without incurring the obligation to install such changes on any previously delivered units.
• On original Tire replacement, company policy prohibits the sale of replacement tires tor all original GEHL machinery. Replacement Wheel Sets are available and tire size information is called-out with the Wheel Sets to facilitate re­ placement tire selection. ALL REPLACEMENT TIRES MUST BE PURCHASED LOCALLY.
• Grease fittings and common attaching hardware, such as Cotter Pins, Set Screws, Woodruff Keys, Screws, Nuts, etc., are included in the parts lists, indented below the part it is (they are) associated with, but NOT illustrated, except where a particular routing or special fastening arrangement MUST be maintained. The hardware listed is for mounting information and is NOT included with the replacement part.
• Refer to the following abbreviations table for fastener descriptions. In the Parts List, if a number precedes the abbreviation, the number represents either quantity required (if other than one per item) or size. Unless otherwise specified, all Cap Screws or Bolts are Grade 5, cadmium or zinc plated; Hexagon Nuts for Grade 5 Screws or Bolts are Grade B; Hexagon Nuts for other Screws or Bolts are Grade A.

GENERAL INFORMATION

• Decal Locations inf onnation is provided to assist in the proper selection and application of new decals, in the event the original decal(s) become(s) damaged or the machine is repainted. Refer to the listing for the illustration reference number, part number, description and quantity of each decal provided in the Kit. Refer to the appropriate illustration(s) for replacement location(s).
• Refer to the SAFETY Chapter for the specific information provided on all of the various Safety Decals furnished in the Decal Kit(s). To ensure proper selection for correct replacement decal(s), compare all of the various closeup location photographs to your machine BEFORE starting to refinish the unit. Then, circle each pictured decal (applicable to your machine) while checking- off its part number in the listing. After you have verified all of the decal needed for replacement, set aside unneeded decals for disposal.

NEW DECAL APPLICATION

Surfaces MUST be free from dirt, dust, grease and other foreign material before applying the new decal. To apply a solidfo 皿ed decal, remove the smaller portion of the decal backing paper and apply this part of the exposed adhesive backing to the clean surface while maintaining proper position and alignment Slowly peel off the other portion of the bacldng paper while applying hand pressure to smooth-out the decal surface. The Decal Set Number for the SIA510 (Gasoline-powered) and SL4610 (Diesel-powered) Agricultural Skid Loaders is 096832. The Set includes the following:

TABLE OF CONTENTS:

GEHL Skid Loader 4615 Service Parts Manual(904592) – PDF DOWNLOAD

Introduction Inside Front Cover
Table of Contents 1
Decal Locations 2-5
Chassis Fuel Tank Grill & Access Covers 6-7
Axles & Drive Components 8-9
Overhead Guard Seat & Engine Access
Cover 10-11
Instrument Panel Wiring & Battery
(After SN14200) 12-13
Instrument Panel Wiring & Battery
(Before SN14201) 14-15
Propulsion Control T-Bar & Linkage
(After SN14200) 16-17
Propulsion Control T-Bar & Linkage
(Before SN14201) 18-19
Lift/Tilt T-Bar Throttle & Linkage 20
Hand Brake & Calipers 21
Hydraulic System (After SN14200) 22-23
Hydraulic System(Before SN14201) 24-25
Hydrostatics System (After SN14200) 26-27
Hydrostatics System(Before SN14201) 28-29
Engine & Related Components
(After SN14200) 30-31
Engine & Related Components
(Before SN14201) 32-33
Air Cleaner Alternator Muffler & Radiator
(After SN14200) 34-35
Air Cleaner Alternator Muffler & Radiator
(Before SN14201) 36-37
Lift A皿s & Hydrolock Mechanism
(After SN13205) 38-39
Lift Arms & Hydrolock Mechanism
(Before SN13206) 40-41
Lift & Tilt Cylinders & Hydraulics 42
Sound Deadening 4 3
Work & Warning Lights · 44-45
Front Auxiliary Hydraulics 46-4 7
Backhoe Adapting Components 48
Pumps Motors Valves & Cylinders 49-63
Right Side Drive Pump (After SN14200) 49
Right Side Drive Pump (Before SN14201 &
After SNl 1800) 50
Page
Right Side Drive Pump(Before SN11801) 51
Left Side Drive Pump (After SN14200) 52
Left Side Drive Pump(Before SN14201 &
After SNl 1800) 53
Left Side Drive Pump(Before SNl 1801) 54
Main Control Valve 5 5
Auxiliary Control Valve 56
Hydrostatic· Drive Motor 57
Columbus Tilt Cylinder· 58
Columbus Lift Cylinder 58
1000 PSI Relief Valve 59
1200 PSI Relief Valve 59
Columbus Grapple Cylinder 59
Single Cessna Gear Pump 60
Dual Gear Pump 60
Later Style Solenoid Valve 61
Early Style Solenoid Valve – 61
Options & Accessories 62-7 5
Cold Planer Water Tank 62-63
Hom Kit 63
Hydraulic Oil Heater Kit 63
Rigid All-Weather Enclosures 64
Overhead Guard Vinyl All-Weather Enclosure 65
Heater Defroster Packages 66
Door Wiper Packages 67
Drawbar Kit 67
Spark Arrestor Muffler Kit 67
Back-up Alarm Packages 68
Enclosed Alternator Kit 68
Amber Warning Beacons 69
Pre-Cleaner Kit 70
Dual Element Air Cleaner Kit 71
Pallet Fork 71
Buckets 72
Dirt & Rock Teeth Kit 72
Attachment Hook Kit 72
Industrial Grapple Fork 73
Dual Gear Pump Kit 74-75
Numerical Index 76-83
Hardware Torque Specifications Inside Back Cover
Attaching Hardware Table Inside Back Cover