GEHL Skid Loader SL6625 Service Parts Manual(904396) – PDF DOWNLOAD

GEHL Skid Loader SL6625 Service Parts Manual(904396) – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

  
DESCRIPTION:

GEHL Skid Loader SL6625 Service Parts Manual(904396) – PDF DOWNLOAD

Introduction:

• When ordering service parts, specify the correct part number, full description, quantity required, and the unit model and serial numbers. Model and serial num­ bers for this unit are on a Decal located inside the Right Chassis Riser, between the Lift Arm and Lift Cylinder.
• “Right” and “Left” are determined from a position sitting on the Seat and facing forward. From this posi­ tion, the Propulsion Control T-bar is on the left and the Lift/Tilt Control T-bar is on the right. GEHL® Company reserves the right to make changes or improvements in the design or construction of any part of the unit without incurring the obligation to install such changes on any previously delivered units.
• On original Tire replacement, company policy prohibits the sale of replacement tires tor all original GEHL machinery. Replacement Wheel Sets are available and tire size information is called-out with the Wheel Sets to facilitate re­ placement tire selection. ALL REPLACEMENT TIRES MUST BE PURCHASED LOCALLY.
• Grease fittings and common attaching hardware, such as Cotter Pins, Set Screws, Woodruff Keys, Screws, Nuts, etc., are included in the parts lists, indented below the part it is (they are) associated with, but NOT illustrated, except where a particular routing or special fastening arrangement MUST be maintained. The hardware listed is for mounting information and is NOT included with the replacement part.
• Refer to the following abbreviations table for fastener descriptions. In the Parts List, if a number precedes the abbreviation, the number represents either quantity required (if other than one per item) or size. Unless otherwise specified, all Cap Screws or Bolts are Grade 5, cadmium or zinc plated; Hexagon Nuts for Grade 5 Screws or Bolts are Grade B; Hexagon Nuts for other Screws or Bolts are Grade A.

GENERAL INFORMATION

• Decal Locations inf onnation is provided to assist in the proper selection and application of new decals, in the event the original decal(s) become(s) damaged or the machine is repainted. Refer to the listing for the illustration reference number, part number, description and quantity of each decal provided in the Kit. Refer to the appropriate illustration(s) for replacement location(s).
• Refer to the SAFETY Chapter for the specific information provided on all of the various Safety Decals furnished in the Decal Kit(s). To ensure proper selection for correct replacement decal(s), compare all of the various closeup location photographs to your machine BEFORE starting to refinish the unit. Then, circle each pictured decal (applicable to your machine) while checking- off its part number in the listing. After you have verified all of the decal needed for replacement, set aside unneeded decals for disposal.

NEW DECAL APPLICATION

Surfaces MUST be free from dirt, dust, grease and other foreign material before applying the new decal. To apply a solidfo 皿ed decal, remove the smaller portion of the decal backing paper and apply this part of the exposed adhesive backing to the clean surface while maintaining proper position and alignment Slowly peel off the other portion of the bacldng paper while applying hand pressure to smooth-out the decal surface. The Decal Set Number for the SIA510 (Gasoline-powered) and SL4610 (Diesel-powered) Agricultural Skid Loaders is 096832. The Set includes the following:

TABLE OF CONTENTS:

GEHL Skid Loader SL6625 Service Parts Manual(904396) – PDF DOWNLOAD

Introduction…………… Inside Front Cover
Table of Contents…………………. 1
Decal Locations…………………. 2-5
Chassis, Fuel Tank, Grill & Access Covers…… 6-7
Axles, Drive Chains & Related Components….. 8-9
Encloser (ROPS), Seat & Engine Cover……. 10-11
Instrument Panel, Wiring &
Electrical Components…………… 12-13
Engine & Related Components.. ……… 14-15
Air Cleaner, Muffler & Radiator……… ．霉16-17
Hydraulic Pump, Filters, Control Valve & Oil Cooler
Single Gear Pump……………… 18-19
Dual Gear Pump………………. 20-21
Hydrostatic Drive Components………… 22-23
Lift厅ilt & Traction T-bar Controls……… 24-25
Lift厅ilt Cylinders & Hydraulic Components…. 26-27
Auxiliary & Backhoe Hydraulics
Before SN5901….. …………. 28-29
After SN5900……………….. 30-31
Lift Arm & Quick-lock Mechanism…….. 32-33
Hand Brake………………….. 34-35
Sound Deadening Components………….. 36
Hydraulic Components…. ……….. 37-46
Lift Cylinder………………….. 3 7
Tilt Cylinder………………….. 3 7
Grapple Cylinder……………….. 38
Planetary Gearcase………………. 38
Drive Motor………………….. 39
Tandem Hydrostatic Pump… ….. 40-41
Single Gear Pump (Rexroth)………….. 42
Single Gear Pump (Cessna)….. …… 42
Dual Gear Pump (Rexroth)…………… 43
Main Control Valve………………. 44
Page
Differential Relief Valve…………… 44
Self-leveling Valves._…………….. 45
Solenoid Valve………………… 46
Accessories………………….. 47-57
Backup Alarm………………… 4 7
Enclosed Alternator……………… 4 7
Hom Kit……………………. 47
Dual Flasher Kit……………….. 48
Strobe Light & Amber Warning Beacon……. 49
High Flow Pump Kit… ……….. 44-45
Rigid AU-weather Enclosure……….. 50-51
Hydraulic Oil Heater Kit…………… 51
Heater Defroster Kit……………… 52
Door Wiper Kit………………… 53
Dual Pump Mounting Kit
(Units Before SN5901)………… 54-55
Air Purifier Kit………………… 55
Dual Pump Kit………………. 56-57
Pre-cleaner Kit………………… 57
Attachments.. ………………. 5 8-64
Buckets……………………. 58
Industrial Grapple………………. 59
Pallet Forks………………….. 60
Industrial Bucket……………….. 61
Brooms, Trenchers, Augers &
Sweeper/Bucket………………. 61
Snow Blower & Truck Loading Spout……. 62
Impulse Breakers……………….. 63
Rock Hound………………….. 64
Numerical Index.. …………….. 65-72
Hardware Torque Specifications.. Inside Back Cover
Attaching Hardware Table…… Inside Back Cover