Gleaner NA Harvesting 3300 Series 3308 3312 Corn Header Service Manual 79036994C – PDF DOWNLOAD

Gleaner NA Harvesting 3300 Series 3308 3312 Corn Header Service Manual 79036994C – PDF DOWNLOAD

FILE DETAILS:

Gleaner NA Harvesting 3300 Series 3308 3312 Corn Header Service Manual 79036994C – PDF DOWNLOAD

Language : English
Pages : 142
Downloadable : Yes
File Type : PDF
Size: 16.8 MB

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

Gleaner NA Harvesting 3300 Series 3308 3312 Corn Header Service Manual 79036994C – PDF DOWNLOAD

General information:
1.1.1 Introduction to this service manual:
This service manual gives information from engineering tests, operating data, and the latest service
techniques at the time of publication. Read this service manual carefully before doing any service on the
machine.
The photos and illustrations used in this service manual were current at the time of publication. Production
changes can cause machines to vary from the photos and the illustrations. The manufacturer reserves the
right to redesign and change machines as necessary without notification.
Machine movement when in normal use determines right-hand and left-hand.
1.1.2 Units of measurement:
Measurements are given in metric units followed by the equivalent in US units. Hardware sizes are given in
millimeters for metric hardware and inches for US hardware.
1.1.3 Table of contents:
This manual has a table of contents at the front. The table of contents shows the divisions. The individual
divisions also have a table of contents.
1.1.4 Page numbers:
All pages have two numbers, such as 01-25. The first number shows the division. The second number
shows the page in the division.
Page numbers occur on the lower right-hand or lower left-hand corner of each page.
1.1.5 Intended use:
This machine is designed solely for use in customary agricultural operations.
Do not use this machine for any application or purpose other than those described in this manual. The
manufacturer accepts no liability for damage or injury resulting from misuse of this machine.
Compliance with the conditions of operation, service and repair as specified by the manufacturer constitute
essential elements for the intended use of this machine.
This machine should be operated, serviced and repaired only by qualified persons familiar with its
characteristics and familiar with the relevant safety rules and procedures.
All generally recognized safety regulations and road traffic regulations must be obeyed at all times.
Any unauthorized modifications performed on this machine will relieve the manufacturer of all liability for
any resulting damage or injury.

TABLE OF CONTENTS:

Gleaner NA Harvesting 3300 Series 3308 3312 Corn Header Service Manual 79036994C – PDF DOWNLOAD

1 General 1-1
1 1 General information 1-3
1 1 1 Introduction to this service manual 1-3
1 1 2 Units of measurement 1-3
1 1 3 Table of contents 1-3
1 1 4 Page numbers 1-3
1 1 5 Intended use 1-3
1 1 6 Proper disposal of waste 1-3
1 2 Safety 1-5
1 2 1 Safety symbol 1-5
1 2 2 Safety messages 1-5
1 2 3 Information messages 1-5
1 2 4 Safety signs 1-5
1 2 5 A word to the technician 1-6
1 2 6 The service manual 1-7
1 2 7 Operation 1-7
1 2 7 1 Prepare for operation 1-7
1 2 7 2 General information 1-7
1 2 7 3 Personal protective equipment 1-8
1 2 7 4 Seat instructions 1-9
1 2 7 5 Shield and guards 1-9
1 2 7 6 Exhaust warning 1-10
1 2 7 7 Flying debris 1-10
1 2 7 8 Handrails 1-10
1 2 7 9 Agricultural chemicals 1-10
1 2 8 Travel on public roads 1-11
1 2 9 Maintenance 1-12
1 2 9 1 General maintenance information 1-12
1 2 9 2 Fire prevention and first aid 1-14
1 2 9 3 High pressure leaks 1-15
1 2 9 4 Tire safety 1-15
1 2 9 5 Replacement parts 1-16
1 3 Cylinder stops 1-17
1 3 1 Engage the header lift cylinder stop 1-17
1 3 2 Disengage the header lift cylinder stop 1-17
1 4 Specifications 1-18
1 4 1 Dimensions and weights 1-18
1 4 2 Header speeds 1-18
1 4 3 Lubrication specifications 1-18
1 5 Lubrication details 1-19
1 5 1 During lubrication 1-19
1 5 2 Sealed bearings 1-19
1 5 3 Lubrication fittings 1-19
1 5 3 1 Torque limiter 1-19
1 5 3 2 Conveyor drive slip clutch 1-20
1 5 3 3 Left driveline 1-20
1 5 3 4 Right driveline 1-21
1 6 Header troubleshooting 1-23
1 7 Bolt torque values 1-24
1 8 Machine identification 1-26
1 8 1 Serial number plate 1-26
3300 Series Corn Header
79036994C
Table of contents , •AGCO
Your Agriculture Company
1 8 2 Serial number description 1-26
1 9 Connect to combine 1-27
1 10 Disconnect from combine 1-30
1 11 Header description 1-32
1 12 Header configuration 1-33
1 12 1 Change header configuration from transverse to axial 1-33
1 12 2 Change header configuration from axial to transverse 1-35
2 Frame
2 1 Tilt frame
2 1 1 Remove the tilt frame
2 1 2 Install the tilt frame
3 Auger 3-1
3 1 Auger 3-3
3 1 1 Remove the auger drive chain 3-3
3 1 2 Install the auger drive chain 3-4
3 1 3 Adjust the auger drive chain 3-4
3 1 4 Remove the auger 3-6
3 1 5 Install the auger 3-6
3 1 6 Adjust the auger 3-7
3 1 7 Remove the auger stripper angles 3-10
3 1 8 Install the auger stripper angles 3-11
3 1 9 Remove the auger pan 3-11
3 1 10 Install the auger pan 3-11
4 Drive system 4-1
4 1 Drive system 4-3
4 1 1 Remove the drive shaft 4-3
4 1 2 Install the drive shaft 4-4
4 2 Driveline 4-7
4 2 1 Remove the implement driveline 4-7
4 2 2 Disassemble the driveline 4-7
4 2 3 Inspect the driveline components 4-11
4 2 4 Assemble the drivel ine 4-11
4 2 5 Install the implement driveline 4-14
5 Electrical system 5-1
5 1 Basic electrical troubleshooting 5-3
5 1 1 Basic troubleshooting procedures 5-3
5 1 2 Tools 5-4
5 1 3 Continuity check 5-4
5 1 4 Voltage check 5-5
5 2 Connectors 5-6
5 2 1 Examine a connector 5-6
5 2 2 Terminal numbers 5-6
5 2 3 Dielectric grease 5-7
5 2 4 Pins and sockets 5-7
5 2 5 Replace a Packard connector 5-8
5 2 6 Replace an AMP connector 5-8
5 2 7 Replace a Power Cord connector 5-9
5 2 8 Replace a Deutsch connector 5-9
5 3 Electrical harness 5-11
6 Shielding 6-1
6 1 Shielding 6-3
3300 Series Corn Header
Remove the inner gathering assembly 6-3
Install the inner gathering assembly 6-3
Adjust the inner gathering assembly height 6-4
Remove the snout 6-5
Install the snout 6-6
Adjust the snout height 6-7
Remove the hood 6-8
Install hood 6-8
Adjust hood clearance 6-9
7 Row units 7-1
7 1 Row units 7-3
7 1 1 Remove the row unit gearbox 7-3
7 1 2 Install the row unit gearbox 7-3
7 1 3 Examine row unit gearbox for lubricant 7-3
7 1 4 Add lubricant to the row unit gearbox 7-4
7 1 5 Remove the chopper gearbox 7-5
7 1 6 Install the chopper gearbox 7-5
7 1 7 Examine chopper gearbox for lubricant 7-5
7 1 8 Add lubricant to the chopper gearbox 7-6
7 1 9 Remove the row unit 7-6
7 1 10 Disassemble the row unit 7-9
7 1 11 Assemble the row unit 7-9
7 1 12 Install the row unit 7-9
7 1 13 Remove the row unit drive 7-11
7 1 14 Install the row unit drive 7-12
7 1 15 Adjust the row unit drive chain 7-13
7 1 16 Check drive chain reservoir for lubricant 7-14
7 1 17 Add lubricant to the drive chain reservoir 7-15
7 1 18 Remove the row unit torque limiter 7-15
7 1 19 Disassemble the row unit torque limiter 7-17
7 1 20 Assemble the row unit torque limiter 7-17
7 1 21 Install the row unit torque limiter 7-18
7 1 22 Remove the stripper plates 7-19
7 1 23 Install the stripper plates 7-21
7 1 24 Remove the snapping rolls 7-22
7 1 25 Install the snapping rolls 7-23
7 1 26 Remove the chopping knives 7-25
7 1 27 Install the chopping knives 7-25
7 2 Gathering chain 7-27
7 2 1 Gathering chain length 7-27
7 2 2 Adjust the gathering chain 7-27
7 2 3 Replace the gathering chain 7-27
7 3 Stripper plates 7-29
7 3 1 Adjust the fixed stripper plates 7-29
7 3 2 Stripper plate indicator 7-29
7 3 3 Index stripper plates 7-29
7 3 4 Stripper plate clean ing 7-30
7 4 Snapping roll blades 7-31
7 4 1 Change snapping roll blades 7-31
7 5 Grass knives 7-32
7 5 1 Adjust the grass knives 7-32
8 Diagrams 8-1
8 1 Wiring diagram 8-3
9 Index lndex-1