Komatsu PC700LC-11E0 Hydraulic Excavator Operation & Maintenance Manual UENAM01652 – PDF DOWNLOAD

Komatsu PC700LC-11E0 Hydraulic Excavator Operation & Maintenance Manual UENAM01652 – PDF DOWNLOAD

IMAGES PREVIEW OF THE MANUAL:

DESCRIPTION:

Komatsu PC700LC-11E0 Hydraulic Excavator Operation & Maintenance Manual UENAM01652 – PDF DOWNLOAD

SERIAL NUMBER
PC700LC-11E0 – K75001 and up

READ THIS MANUAL:

• This manual gives details of the operation and methods of inspection and maintenance for this machine that
  must be obeyed in order to use the machine safely. Most accidents are caused by the failure to follow fundamental
  safety rules for the operation and maintenance of machines.
• Read, understand and follow all precautions and warnings in this manual and on the machine before performing
  operation and maintenance. Failure to do so may result in serious injury or death.
• Komatsu cannot predict every circumstance that might involve a potential hazard when the machine is used.
• Therefore, the safety messages in this manual and on the machine may not include all possible safety precautions.
  If you perform any operation, inspection, or maintenance under conditions that are not described in this manual,
  understand that it is your responsibility to take the necessary precautions to ensure safety. In no event should
  you or others engage in the prohibited uses or actions described in this manual. It is dangerous to perform improper
  operation and maintenance of the machine. It may cause serious injury or death.
• If you sell the machine, be sure to give this manual to the new owner together with the machine.
• Always keep this Operation and Maintenance Manual in the indicated location so that all relevant personnel can
  read it at any time.

TABLE OF CONTENTS:

Komatsu PC700LC-11E0 Hydraulic Excavator Operation & Maintenance Manual UENAM01652 – PDF DOWNLOAD

FOREWORD 3
READ THIS MANUAL 4
KOMATSU MACHINE OPERATOR PRIVACY POLICY 5
SAFETY INFORMATION 8
SAFETY LABELS 9
NOISE 10
VIBRATION LEVELS 11
VIBRATION – OPERATING CONDITION 11
GUIDE TO REDUCE VIBRATION LEVELS ON MACHINE 11
INTRODUCTION 13
MAIN USE OF MACHINE 13
DEMOLITION WORK 13
DIRECTIONS OF MACHINE 13
VISIBILITY FROM OPERATOR’S SEAT 14
ENGINE TECHNOLOGY TO CONFORM EXHAUST GAS EMISSION 15
PRODUCT INFORMATION 16
LOCATION OF PRODUCT IDENTIFICATION NUMBER (PIN)/MACHINE SERIAL NO PLATE 16
LOCATION OF ENGINE NUMBER PLATE 16
FLUORINATED GREENHOUSE GASES 17
SERVICE METER LOCATION 17
YOUR MACHINE SERIAL NUMBERS AND DISTRIBUTOR 17
SERIAL PLATE 18
DECLARATION OF CONFORMITY 19
CONTENTS 20
ABBREVIATION LIST 24
SAFETY 25
SAFETY LABELS 26
LOCATION OF SAFETY LABELS 27
CONTENTS OF SAFETY LABELS 29
GENERAL PRECAUTIONS COMMON TO OPERATION AND MAINTENANCE 37
PRECAUTIONS BEFORE STARTING OPERATION 37
ENSURE SAFE OPERATION 37
UNDERSTAND THE MACHINE 37
PREPARATIONS FOR SAFE OPERATION 37
PRECAUTIONS FOR SAFETY-RELATED EQUIPMENT 37
INSPECT MACHINE 37
WEAR WELL-FITTING CLOTHES AND PROTECTIVE EQUIPMENT 37
KEEP MACHINE CLEAN 38
PRECAUTIONS FOR INSIDE OPERATOR’S COMPARTMENT 38
PROVIDE FIRE EXTINGUISHER AND FIRST AID KIT 38
IF ANY PROBLEM IS FOUND 38
PRECAUTIONS TO PREVENT FIRE 38
ACTIONS IF FIRE OCCURS 38
PREVENT FIRE 39
PRECAUTIONS WHEN GETTING ON OR OFF MACHINE 40
USE HANDRAILS AND STEPS WHEN GETTING ON OR OFF MACHINE 40
NO JUMPING ON OR OFF MACHINE 41
LIFTING OF PERSONNEL PROHIBITED 41
NO PEOPLE ON ATTACHMENTS 41
PRECAUTIONS WHEN STANDING UP FROM OPERATOR’S SEAT 41
PRECAUTIONS WHEN LEAVING MACHINE 41
EMERGENCY EXIT FROM OPERATOR’S CAB 42
ELECTROMAGNETIC INTERFERENCE 42
DO NOT GET CAUGHT IN WORK EQUIPMENT 42
PRECAUTIONS RELATED TO PROTECTIVE STRUCTURES 42
PROTECTION AGAINST FALLING, FLYING OR INTRUDING OBJECTS 43
UNAUTHORIZED MODIFICATION 43
PRECAUTIONS RELATED TO ATTACHMENTS AND OPTIONS 43
PRECAUTIONS RELATED TO CAB GLASS 44
PRECAUTIONS WHEN RUNNING ENGINE INSIDE BUILDING 44
PRECAUTIONS FOR OPERATION 45
PRECAUTIONS FOR JOBSITE 45
INVESTIGATE AND CONFIRM JOBSITE CONDITIONS 45
PRECAUTIONS WHEN WORKING ON LOOSE GROUND 45
DO NOT GO CLOSE TO HIGH-VOLTAGE CABLES 45
ENSURE GOOD VISIBILITY 46
CHECK SIGNS AND SIGNALMAN’S SIGNALS 46
BEWARE OF ASBESTOS DUST 46
START ENGINE 47
USE WARNING TAGS 47
CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE 47
PRECAUTIONS WHEN STARTING ENGINE 48
IN COLD WEATHER 48
START ENGINE WITH JUMPER CABLES 48
PRECAUTIONS FOR OPERATION 49
CHECKS BEFORE OPERATION 49
PRECAUTIONS WHEN TRAVELLING IN FORWARD OR REVERSE AND SWINGING 49
PRECAUTIONS WHEN TRAVELLING 50
PRECAUTIONS WHEN TRAVELING ON SLOPES 51
PRECAUTIONS WHEN OPERATING ON SLOPES 52
PROHIBITED OPERATIONS 52
PRECAUTIONS WHEN OPERATING ON SNOW OR FROZEN SURFACES 54
PRECAUTIONS WHEN PARKING MACHINE 54
PRECAUTIONS FOR TRANSPORTATION 55
PRECAUTIONS WHEN LOADING AND UNLOADING 55
TOWING AND BEING TOWED 56
PRECAUTIONS FOR TOWING AND BEING TOWED 56
LIFTING OPERATION BY USING BUCKET WITH HOOK 56
PRECAUTIONS FOR LIFTING OPERATIONS 56
PRECAUTIONS FOR MAINTENANCE 58
PRECAUTIONS BEFORE STARTING INSPECTION AND MAINTENANCE 58
DISPLAY WARNING TAG DURING INSPECTION AND MAINTENANCE 58
KEEP WORK PLACE CLEAN AND TIDY 58
SELECT SUITABLE PLACE FOR INSPECTION AND MAINTENANCE 58
ONLY AUTHORIZED PERSONNEL 58
APPOINT LEADER WHEN WORKING WITH OTHERS 58
STABILITY 59
GUARDS 59
END OF SERVICE LIFE 59
STOP ENGINE BEFORE CARRYING OUT INSPECTION AND MAINTENANCE 59
TWO WORKERS FOR MAINTENANCE WHEN ENGINE IS RUNNING 59
PRECAUTIONS WHEN INSTALLING, REMOVING, OR STORING ATTACHMENTS 60
PRECAUTIONS FOR WORKING AT HIGH PLACES 60
PRECAUTIONS WHEN WORKING ON MACHINE 60
PRECAUTIONS WHEN WORKING UNDER MACHINE OR WORK EQUIPMENT 61
USE PROPER TOOLS 61
PRECAUTIONS FOR CHECK AND MAINTENANCE 61
TURN BATTERY DISCONNECT SWITCH TO OFF POSITION 61
PRECAUTIONS FOR WELDING 61
HANDLE BATTERY 62
PRECAUTIONS WHEN USING HAMMER 62
PRECAUTIONS FOR HIGH-TEMPERATURE COOLANT 63
PRECAUTIONS FOR HIGH-TEMPERATURE OIL 63
PRECAUTIONS FOR HIGH-TEMPERATURE PARTS 63
PRECAUTIONS FOR HIGH-PRESSURE OIL 63
PRECAUTIONS FOR HIGH-PRESSURE FUEL 64
HANDLE HIGH-PRESSURE HOSES AND PIPING 64
PRECAUTIONS FOR HIGH VOLTAGE 64
PRECAUTIONS FOR NOISE 64
PRECAUTIONS FOR HIGH-PRESSURE GREASE WHEN ADJUSTING TRACK TENSION 65
DO NOT DISASSEMBLE RECOIL SPRING 65
HANDLE ACCUMULATOR AND GAS SPRING 65
PRECAUTIONS FOR COMPRESSED AIR 66
MAINTENANCE OF AIR CONDITIONER 66
CHEMICAL HAZARD 66
PRECAUTIONS FOR DISPOSING OF WASTE MATERIALS 66
METHOD FOR SELECTING WINDOW WASHER FLUID 66
PERIODIC REPLACEMENT OF DEFINED LIFE PARTS 66
PRECAUTIONS FOR DEF 68
GENERAL CHARACTER AND PRECAUTIONS FOR HANDLING 68
PRECAUTIONS FOR ADDING 68
PRECAUTIONS FOR STORING 68
PRECAUTIONS FOR FIRE HAZARD AND LEAKAGE 68
OTHER PRECAUTIONS 68
OPERATION 69
GENERAL VIEW 70
MACHINE EQUIPMENT NAME 70
CAB EQUIPMENT NAMES 72
CONTROLS AND GAUGES NAMES 73
MACHINE MONITOR EQUIPMENT NAME 74
EXPLANATION OF COMPONENTS 76
EXPLANATION OF MACHINE MONITOR EQUIPMENT 76
BASIC OPERATION OF MACHINE MONITOR 77
WARNING DISPLAY 83
ACTION LEVEL DISPLAY 85
ENGINE COOLANT TEMPERATURE CAUTION LAMP 89
HYDRAULIC OIL TEMPERATURE CAUTION LAMP 89
FUEL LEVEL CAUTION LAMP 90
SYSTEM CAUTION LAMP 90
HYDRAULIC SYSTEM CAUTION LAMP 90
KDPF SYSTEM CAUTION LAMP 91
KDPF SOOT ACCUMULATION CAUTION LAMP 91
DEF LEVEL CAUTION LAMP 92
DEF SYSTEM CAUTION LAMP 92
DEF SYSTEM HIGH TEMPERATURE STOP CAUTION LAMP 93
ENGINE SYSTEM CAUTION LAMP 93
ENGINE SUDDEN STOP BY AUTO IDLE STOP CAUTION LAMP 93
ENGINE OIL PRESSURE CAUTION LAMP 94
ENGINE OIL LEVEL CAUTION LAMP 94
ENGINE OVERRUN CAUTION LAMP 94
RADIATOR COOLANT LEVEL CAUTION LAMP 95
CHARGE LEVEL CAUTION LAMP 95
AIR CLEANER CLOGGING CAUTION LAMP 95
AIR CONDITIONER SYSTEM CAUTION LAMP 95
OVERLOAD CAUTION LAMP 96
MAINTENANCE TIME CAUTION LAMP 96
SEATBELT CAUTION LAMP 97
CAMERA SYSTEM CAUTION LAMP 97
CAMERA SYSTEM CAUTION LAMP 98
PILOT DISPLAY AND METER DISPLAY 98
MONITOR SWITCHES 108
FUNCTION SWITCHES 117
USER MENU 123
SWITCHES 157
STARTING SWITCH 158
FUEL CONTROL DIAL 158
CIGARETTE LIGHTER 158
SWING LOCK SWITCH 158
LAMP SWITCH 159
HORN SWITCH 159
ONE-TOUCH POWER MAXIMIZING SWITCH 159
ROOM LAMP SWITCH 160
PUMP SECONDARY DRIVE SWITCH 160
SWING PARKING BRAKE CANCEL SWITCH 161
LOCK LEVER AUTOMATIC LOCK CANCEL SWITCH 161
REVOLVING LAMP SWITCH 162
LOWER WIPER SWITCH 162
ENGINE SHUTDOWN SECONDARY SWITCH 163
SEAT HEATER SWITCH 163
ADDITIONAL LAMPS SWITCH 164
MACHINE PUSH-UP SWITCH 164
STAIRCASE LIGHTING SWITCH 164
CONTROL LEVERS AND PEDALS 165
LOCK LEVER 165
TRAVEL LEVER 167
WORK EQUIPMENT CONTROL LEVER 167
OTHER EQUIPMENT 168
EMERGENCY ESCAPE HAMMER 168
METHOD FOR USING DOOR LOCK 168
CAB DOOR HINGE 169
CAP AND COVER WITH LOCK 169
DRINK BOX 170
MAGAZINE BOX 170
CUP HOLDER 170
ASHTRAY 170
POWER SUPPLY OUTLET 171
FUSE 171
CIRCUIT BREAKER 173
TOOL BOX 174
FIRE EXTINGUISHER 174
BATTERY DISCONNECT SWITCH 174
SYSTEM OPERATING LAMP 175
GREASE PUMP 176
HANDLE Komatsu Diesel Particulate Filter (KDPF) 179
Komatsu Closed Crankcase Ventilation (KCCV) 190
HANDLE UREA SCR SYSTEM WARNING 190
KOMTRAX 204
MACHINE OPERATIONS AND CONTROLS 206
CHECKS AND ADJUSTMENT BEFORE STARTING ENGINE 206
METHOD FOR WALK-AROUND CHECK 206
METHOD FOR CHECKING BEFORE STARTING 207
METHOD FOR ADJUSTING 219
METHOD FOR OPERATIONS AND CHECKS BEFORE STARTING ENGINE 234
METHOD FOR STARTING ENGINE 236
METHOD FOR MANUAL PREHEATING WHEN STARTING ENGINE 238
TURBOCHARGER PROTECTION FUNCTION 239
AMBIENT TEMPERATURE RANGE FOR OPERATION AND STORAGE 239
METHOD FOR OPERATIONS AND CHECKS AFTER STARTING ENGINE 240
METHOD FOR CHECKING STARTING CONDITION AND UNUSUAL NOISE OF ENGINE 240
METHOD FOR CHECKING LOW-SPEED RUN AND ACCELERATION OF ENGINE 241
METHOD FOR RUNNING-IN THE NEW MACHINE 241
METHOD FOR ENGINE WARM-UP OPERATION 241
METHOD FOR HYDRAULIC SYSTEM WARM-UP OPERATION 244
METHOD FOR OPERATION AFTER COMPLETION OF WARM-UP OPERATION 248
METHOD FOR STOPPING ENGINE 249
METHOD FOR STARTING MACHINE (TRAVEL FORWARD AND REVERSE) AND STOPPING MACHINE 252
PREPARATIONS FOR MOVING MACHINE 252
METHOD FOR TRAVELLING FORWARD 253
METHOD FOR TRAVELLING REVERSE 253
METHOD FOR STOPPING MACHINE 254
METHOD FOR STEERING MACHINE 255
METHOD FOR STEERING (CHANGE THE DIRECTION) MACHINE 255
METHOD FOR SWINGING MACHINE 257
METHOD FOR OPERATING WORK EQUIPMENT 257
HANDLE WORKING MODE 259
METHOD FOR SELECTING WORKING MODE 259
METHOD FOR USING ONE-TOUCH POWER MAXIMIZING FUNCTION 260
ECONOMY MODE SELECTION 260
PROHIBITED OPERATIONS 261
PROHIBITION OF OPERATIONS USING SWING FORCE 261
PROHIBITION OF OPERATIONS USING TRAVEL FORCE 261
PROHIBITION OF OPERATIONS USING HYDRAULIC CYLINDERS TO STROKE END 261
PROHIBITION OF OPERATIONS USING BUCKET DROPPING FORCE 262
PROHIBITION OF OPERATIONS USING BUCKET AS LEVER 262
PROHIBITION OF OPERATIONS USING MACHINE DROPPING FORCE 262
PROHIBITION OF DIGGING OPERATION AT AN ANGLE WITHOUT ENGAGING TEETH 263
PROHIBITION OF DIGGING OPERATION ON HARD ROCKY GROUND 263
PROHIBITION OF OPERATIONS WHEN MACHINE IS NOT STABLE 263
PROHIBITION OF SWINGING OR TRAVELLING WHEN ROCK IS ON TOP OF TRACK ASSEMBLY 264
PROHIBITION OF SUDDEN LEVER OR PEDAL SHIFT DURING HIGH SPEED TRAVEL 264
PROHIBITION OF HIGH-SPEED TRAVEL OPERATIONS ON ROUGH GROUND 264
DO NOT TRAVEL LONG -TIME CONTINUOUSLY 265
PRECAUTIONS FOR OPERATION 265
PRECAUTIONS FOR TRAVELLING 265
PRECAUTIONS FOR HIGH SPEED TRAVEL 265
PERMISSIBLE DEPTH OF WATER, SOIL AND DIRT 266
PRECAUTIONS FOR WORKING ON SLOPE 267
METHOD FOR ESCAPING FROM MUD 268
RECOMMENDED APPLICATIONS 269
DIGGING WORK 269
DITCHING WORK 270
LOADING WORK 270
EFFECTIVE USE OF HYDRAULIC EXCAVATOR 270
METHOD FOR REPLACING AND INVERTING BUCKET 271
METHOD FOR CHANGING BUCKET 271
METHOD FOR PARKING MACHINE 273
METHOD FOR CHECKING AFTER FINISHING WORK 274
LOCK 275
METHOD FOR OPENING AND CLOSING CAP WITH LOCK 275
METHOD FOR OPENING AND CLOSING COVER WITH LOCK 276
METHOD FOR OPENING AND CLOSING ENGINE HOOD 276
METHOD FOR OPENING AND CLOSING DEF TANK FILLER CAP COVER 278
METHOD FOR OPENING AND CLOSING CAB DOOR 279
HANDLE AIR CONDITIONER 280
EXPLANATION OF AIR CONDITIONER EQUIPMENT 281
OFF SWITCH 281
FAN SWITCH 281
TEMPERATURE CONTROL SWITCH 282
VENT SELECTOR SWITCH 283
AUTO SWITCH 284
FRESH/RECIRC AIR SELECTOR SWITCH 284
DISPLAY MONITOR 284
AIR CONDITIONER SWITCH 285
SUNLIGHT SENSOR 285
METHOD FOR OPERATING AIR CONDITIONER 285
METHOD FOR AUTOMATIC OPERATION 286
METHOD FOR STOPPING AUTOMATIC OPERATION 287
METHOD FOR MANUAL OPERATION 287
METHOD FOR STOPPING MANUAL OPERATION 289
METHOD FOR OPERATING WITH COLD AIR TO FACE AND WARM AIR TO FEET 289
METHOD FOR OPERATING DEFROSTER 291
HANDLING RADIO 294
EXPLANATION OF RADIO EQUIPMENT 294
POWER BUTTON 294
BAND/AUX SELECTOR BUTTON 294
VOLUME CONTROL BUTTON 294
TUNING/TIME ADJUSTMENT BUTTON 294
PRESET BUTTON 295
DISPLAY SELECTOR BUTTON 295
SOUND CONTROL BUTTON 295
DISPLAY 295
AUX 295
METHOD FOR CONTROLLING RADIO 296
METHOD FOR ADJUSTING FREQUENCY 296
METHOD FOR ADJUSTING FREQUENCY (AUTO PRESETTING) 297
METHOD FOR CALLING PRESET 297
METHOD FOR REGISTERING PRESET 297
METHOD FOR ADJUSTING SOUND BALANCE 298
METHOD FOR ADJUSTING HIGH REGISTER RANGE (TREBLE) 298
METHOD FOR ADJUSTING LOW REGISTER RANGE (BASS) 298
METHOD FOR ADJUSTING CLOCK 298
STOW ANTENNA 299
SPACE FOR RADIO CASSETTE 299
KomVision 300
PRECAUTIONS WHEN USING KomVision 300
MONITOR DISPLAY 300
TRANSPORTATION 302
PRECAUTIONS FOR TRANSPORTING MACHINE 302
SELECT TRANSPORTATION METHOD 302
METHOD FOR LIFTING MACHINE 302
PRECAUTIONS FOR LOADING MACHINE 303
MACHINE CONFIGURATION FOR TRANSPORTATION 304
SPREAD AND NARROW TRACK FRAME GAUGE 307
PRECAUTIONS FOR SPREADING AND NARROWING TRACK FRAME GAUGE 307
NARROW TRACK FRAME GAUGE 307
SPREAD TRACK FRAME GAUGE 308
COLD WEATHER OPERATION 310
COLD WEATHER OPERATION INFORMATION 310
FUEL AND LUBRICANTS 310
COOLANT 310
DEF 310
BATTERY 310
PRECAUTIONS AFTER DAILY WORK COMPLETION IN COLD WEATHER 311
AFTER COLD WEATHER SEASON 312
PRECAUTIONS FOR LONG-TERM STORAGE 313
PREPARATION FOR LONG-TERM STORAGE 313
MAINTENANCE DURING LONG-TERM STORAGE 313
STARTING MACHINE AFTER LONG-TERM STORAGE 313
TROUBLES AND ACTIONS 315
ACTIONS WHEN RUNNING OUT OF FUEL 315
PROCEDURES FOR BLEEDING AIR FROM FUEL CIRCUIT 315
PHENOMENA THAT ARE NOT FAILURES 316
PRECAUTIONS FOR TOWING MACHINE 316
PRECAUTIONS FOR SEVERE JOB CONDITION 317
PRECAUTIONS FOR DISCHARGED BATTERY 318
METHOD FOR REMOVING AND INSTALLING BATTERY 318
PRECAUTIONS FOR CHARGING BATTERY 320
START ENGINE WITH JUMPER CABLES 321
OTHER TROUBLE 322
PHENOMENA AND ACTIONS FOR ELECTRICAL SYSTEM 322
PHENOMENA AND ACTIONS FOR CHASSIS 323
PHENOMENA AND ACTIONS FOR ENGINE RELATED PARTS 324
IF MACHINE MONITOR SHOWS WARNING DISPLAY 326
MAINTENANCE 329
PRECAUTIONS FOR MAINTENANCE 330
CHECK SERVICE METER READING 330
KOMATSU GENUINE REPLACEMENT PARTS 330
KOMATSU GENUINE LUBRICANTS 330
ALWAYS USE CLEAN WASHER FLUID 330
FRESH AND CLEAN LUBRICANTS 330
CHECK DRAINED OIL AND USED FILTER 330
PRECAUTIONS FOR REFILLING OIL OR FUEL 330
PRECAUTIONS FOR ADDING DEF 330
WELDING INSTRUCTIONS 330
DO NOT DROP THINGS INSIDE MACHINE 330
PRECAUTIONS FOR KDPF 331
PRECAUTIONS FOR SCR ASSEMBLY 331
DUSTY JOBSITES 331
AVOID MIXING OIL 331
LOCK INSPECTION COVERS 331
BLEED AIR FROM HYDRAULIC CIRCUIT 331
PRECAUTIONS WHEN INSTALLING HYDRAULIC HOSES 331
CHECKS AFTER INSPECTION AND MAINTENANCE 331
FUEL AND LUBRICANTS TO MATCH THE AMBIENT TEMPERATURE 332
CLOSE ENGINE HOOD SECURELY 332
PRECAUTIONS WHEN YOU CLEAN WORK EQUIPMENT CONTROL LEVER 332
OUTLINE OF MAINTENANCE 333
HANDLE OIL, FUEL, COOLANT, AND PERFORMING OIL CLINIC 333
OIL 333
FUEL 333
BIO-FUEL 334
PARAFFIN-BASED FUEL 335
COOLANT AND WATER FOR DILUTION 336
DEF 336
GREASE 337
PERFORM KOWA (Komatsu Oil Wear Analysis) 337
STORE OIL AND FUEL 338
STORE DEF 338
FILTER 338
HANDLE ELECTRICAL COMPONENTS 338
STANDARD TIGHTENING TORQUE FOR BOLTS AND NUTS 340
MAINTENANCE SCHEDULE 342
MAINTENANCE SCHEDULE TABLE 342
MAINTENANCE INTERVAL FOR HYDRAULIC BREAKER 343
MAINTENANCE PROCEDURE 345
INITIAL 100 HOURS MAINTENANCE (ONLY AFTER THE FIRST 100 HOURS) 345
INITIAL 500 HOURS MAINTENANCE (ONLY AFTER THE FIRST 500 HOURS) 345
WHEN REQUIRED 345
METHOD FOR CHECKING, CLEANING AND REPLACING AIR CLEANER 345
METHOD FOR CLEANING INSIDE OF COOLING SYSTEM 350
METHOD FOR CHECKING LOOSENESS AND TIGHTENING TRACK SHOE BOLTS 352
METHOD FOR CHECKING AND ADJUSTING TRACK TENSION 353
METHOD FOR REPLACING BUCKET TEETH (KMAX) 354
METHOD FOR REMOVING SLINGING LOOP 356
METHOD FOR REPLACING BUCKET TEETH (HORIZONTAL PIN TYPE) 357
METHOD FOR ADJUSTING BUCKET CLEARANCE 359
METHOD FOR CHECKING WINDOW WASHER FLUID LEVEL, ADDING FLUID 359
METHOD FOR CHECKING AND MAINTENANCE AIR CONDITIONER 360
METHOD FOR REPLACING ADDITIONAL FILTER ELEMENT FOR BREAKER 361
METHOD FOR WASHING WASHABLE FLOOR 362
METHOD FOR BLEEDING AIR FROM HYDRAULIC CIRCUIT 366
METHOD FOR CLEANING LINE FILTER AND REMOVING DIRT 368
METHOD FOR CLEANING PILOT LINE FILTER AND REMOVING DIRT 368
METHOD FOR CHECKING CAMERA VISIBILITY 369
CHECKS BEFORE STARTING 369
EVERY 10 HOURS MAINTENANCE 370
METHOD FOR LUBRICATING 370
EVERY 100 HOURS MAINTENANCE 372
METHOD FOR LUBRICATING SWING CIRCLE 372
EVERY 250 HOURS MAINTENANCE 372
METHOD FOR CHECKING OIL LEVEL IN FINAL DRIVE CASE, ADDING OIL 372
METHOD FOR CHECKING BATTERY ELECTROLYTE LEVEL 373
METHOD FOR CHECKING LOOSENESS AND TIGHTENING TRACK FRAME AND CENTRE FRAME CONNECTING BOLTS 374
EVERY 500 HOURS MAINTENANCE 374
METHOD FOR CHANGING OIL IN ENGINE OIL PAN, REPLACING ENGINE OIL FILTER CARTRIDGE 375
METHOD FOR REPLACING FUEL PRE-FILTER CARTRIDGE 376
METHOD FOR CHECKING SWING PINION GREASE LEVEL, ADD GREASE 378
METHOD FOR CHECKING AND CLEANING RADIATOR FINS, OIL COOLER FINS, AFTERCOOLER FINS, FUEL COOLER FINS, AND AIR CONDITIONER CONDENSER FINS 379
METHOD FOR CLEANING AIR CONDITIONER FRESH/RECIRC FILTERS 380
METHOD FOR CLEANING PTO LUBRICATION FILTER STRAINER 382
EVERY 1000 HOURS MAINTENANCE 382
CHECK STRUCTURES FOR CRACKS 383
METHOD FOR REPLACING HYDRAULIC OIL FILTER ELEMENT 383
METHOD FOR CHANGE OIL IN SWING MACHINERY CASE 384
METHOD FOR CHANGING OIL IN PTO CASE 385
METHOD FOR REPLACING FUEL MAIN FILTER CARTRIDGE 386
METHOD FOR CHECKING ALL TIGHTENING POINTS OF ENGINE INTAKE PIPE CLAMPS 388
METHOD FOR CHECKING WELDED STRUCTURE 388
METHOD FOR CHECKING AND RELEASING NITROGEN GAS CHARGE PRESSURE IN ACCUMULATOR (FOR BREAKER) 390
METHOD FOR REPLACING HYDRAULIC TANK BREATHER ELEMENT 390
METHOD FOR REPLACING DEF TANK BREATHER ELEMENT 391
METHOD FOR CHECKING AND REPLACING ALTERNATOR AND AIR CONDITIONER COMPRESSOR DRIVE BELT 392
EVERY 2000 HOURS MAINTENANCE 392
METHOD FOR CHANGING OIL IN FINAL DRIVE CASE 392
METHOD FOR CLEANING HYDRAULIC TANK STRAINER 393
METHOD FOR CHECKING AND RELEASING NITROGEN GAS CHARGE PRESSURE IN ACCUMULATOR (FOR CONTROL CIRCUIT) 394
METHOD FOR CHECKING ALTERNATOR 397
METHOD FOR CHECKING AND ADJUSTING ENGINE VALVE CLEARANCE 397
METHOD FOR REPLACING KCCV FILTER ELEMENT 397
METHOD FOR REPLACING DEF FILTER 401
EVERY 4000 HOURS MAINTENANCE 403
REPLACE DEFINED LIFE PARTS 403
METHOD FOR CHECKING WATER PUMP 404
CHECK OPERATING CONDITION OF COMPRESSOR 404
METHOD FOR CHECKING STARTING MOTOR 404
METHOD FOR REPLACING ACCUMULATOR (FOR CONTROL CIRCUIT) 404
METHOD FOR CHECKING FOR LOOSENESS OF ENGINE HIGH-PRESSURE PIPING CLAMP, HARDENING OF RUBBER 405
METHOD FOR CHECKING FOR MISSING FUEL SPRAY PREVENTION CAP, HARDENING OF RUBBER 406
METHOD FOR REPLACING RADIATOR CAP 406
EVERY 4500 HOURS MAINTENANCE 407
METHOD FOR CLEANING KDPF 407
METHOD FOR CLEANING DEF TANK 407
METHOD FOR REPLACING DEF FILLER PORT FILTER 407
METHOD FOR CLEANING FUEL DOSER 407
CHECK FOR MISSING FUEL SPRAY PREVENTION CAP ON FUEL DOSER PIPING, HARDENING OF RUBBER 408
EVERY 5000 HOURS MAINTENANCE 408
METHOD FOR CHANGING OIL IN HYDRAULIC TANK 408
EVERY 8000 HOURS MAINTENANCE 409
METHOD FOR REPLACING ENGINE HIGH-PRESSURE PIPING CLAMP 409
METHOD FOR REPLACING FUEL SPRAY PREVENTION CAP 409
EVERY 9000 HOURS MAINTENANCE 409
METHOD FOR REPLACING DEF HOSE 410
METHOD FOR REPLACING FUEL SPRAY PREVENTION CAP ON FUEL DOSER PIPING 410
END OF SERVICE LIFE 410
SPECIFICATIONS 411
SPECIFICATIONS 412
SPECIFICATIONS: PC700LC-11 E0 412
EXPLANATION OF LIFT CAPACITY CHART (1-PIECE BOOM) 413
ATTACHMENTS AND OPTIONS 417
PRECAUTIONS FOR USING ATTACHMENT AND OPTIONS 418
PRECAUTIONS WHEN SELECTING 418
READ THE OPERATION AND MAINTENANCE MANUAL THOROUGHLY 418
PRECAUTIONS WHEN REMOVING AND INSTALLING 418
PRECAUTIONS WHEN USING 418
HANDLE BUCKET WITH HOOK 420
PRECAUTIONS FOR OPERATION 420
PRECAUTIONS FOR LIFTING OPERATIONS 420
HANDLE MACHINE READY FOR INSTALLATION OF ATTACHMENT 421
EXPLANATION OF COMPONENTS ON MACHINE EQUIPPED WITH ATTACHMENT 421
STOP VALVE 421
ATTACHMENT CONTROL PEDAL 422
LOCK PIN 422
METHOD FOR HYDRAULIC CIRCUIT CONNECTION 423
METHOD FOR CONNECTING HYDRAULIC CIRCUIT 423
PEDAL OPERATION AND OIL FLOW OF MACHINE EQUIPPED WITH ATTACHMENT 424
METHOD FOR REMOVING AND INSTALLING ATTACHMENT 424
METHOD FOR REMOVING ATTACHMENT 425
METHOD FOR INSTALLING ATTACHMENT 426
LONG-TERM STORAGE 428
ARM/PIN INFORMATION 429
ATTACHMENTS AND OPTIONS 430
INSTALL ATTACHMENT 430
TRACK SHOES SELECTION 431
REPLACEMENT PARTS 433
PERIODIC REPLACEMENT OF DEFINED LIFE PARTS 434
DEFINED LIFE PARTS LIST 434
CONSUMABLE PARTS 435
CONSUMABLE PARTS 435
RECOMMENDED FUEL, COOLANT, AND LUBRICANT 436
LUBRICATION CHART 438
USE OF FUEL, COOLANT AND LUBRICANTS TO ACCORDING TO AMBIENT TEMPERATURE 439
RECOMMENDED BRANDS AND QUALITIES OTHER THAN KOMATSU GENUINE OILS 440
INDEX 441