Kymco People 125/150 Service Manual - PDF DOWNLOAD

Kymco People 125/150 Service Manual - PDF DOWNLOAD

FILE DETAILS:

Kymco People 125/150 Service Manual - PDF DOWNLOAD

Language : English
Pages : 185
Downloadable : Yes
File Type : PDF

IMAGES PREVIEW OF THE MANUAL:

TABLE OF CONTENTS:

Kymco People 125/150 Service Manual - PDF DOWNLOAD

1. GENERAL INFORMATION
2. FRAME COVERS/EXHAUST MUFFLER
3. INSPECTION/ADJUSTMENT
4. LUBRICATION SYSTEM
5. FUEL SYSTEM
6. ENGINE REMOVAL/INSTALLATION
7. CYLINDER HEAD/VALVES
8. CYLINDER/PISTON
9. DRIVE AND DRIVEN PULLEYS/
KICK STARTER
10. FINAL REDUCTION
11. CRANKCASE/CRANKSHAFT
12. FRONT WHEEL/FRONT BRAKE/
FRONT SUSPENSION
13. REAR WHEEL/REAR BRAKE/
REAR SUSPENSION
14. BATTERY/CHARGING SYSTEM/
A.C. GENERATOR
15. IGNITION SYSTEM
16. STARTING SYSTEM
17. LIGHTS/INSTRUMENTS/SWITCHES

DESCRIPTION:

Kymco People 125/150 Service Manual - PDF DOWNLOAD

GENERAL INFORMATION:

PEOPLE 125/150

SERVICE PRECAUTIONS:

• Make sure to install new gaskets, O-rings, circlips, cotter pins, etc. when reassembling.
• When tightening bolts or nuts, begin with larger-diameter to smaller ones at several times, and tighten to the specified torque diagonally. 
• Use genuine parts and lubricants. 
• When servicing the motorcycle, be sure to use special tools for removal and installation.
• After disassembly, clean removed parts. Lubricate sliding surfaces with engine oil before reassembly.
• Apply or add designated greases and lubricants to the specified lubrication points. 
• After reassembly, check all parts for proper tightening and operation. 
• When two persons work together, pay attention to the mutual working safety.
• Disconnect the battery negative (-) terminal before operation. n When using a spanner or other tools, make sure not to damage the motorcycle surface. 
• After operation, check all connecting points, fasteners, and lines for proper connection and installation. 
• When connecting the battery, the positive (+) terminal must be connected first. 
• After connection, apply grease to the battery terminals.
• Terminal caps shall be installed securely. n If the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. 
• After operation, terminal caps shall be installed securely. n When taking out the connector, the lock on the connector shall be released before operation. 
• Hold the connector body when connecting or disconnecting it. n Do not pull the connector wire. n Check if any connector terminal is bending, protruding or loose. 
• The connector shall be inserted completely. 
• If the double connector has a lock, lock it at the correct position. 
• Check if there is any loose wire. n Before connecting a terminal, check for damaged terminal cover or loose negative terminal. 
• Check the double connector cover for proper coverage and installation. 
• Insert the terminal completely. n Check the terminal cover for proper coverage.
• Do not make the terminal cover opening face up. 
• Secure wire harnesses to the frame with their respective wire bands at the designated locations. Tighten the bands so that only the insulated surfaces contact the wire harnesses. 
• After clamping, check each wire to make sure it is secure. 
• Do not squeeze wires against the weld or its clamp.
• After clamping, check each harness to make sure that it is not interfering with any moving or sliding parts. 
• When fixing the wire harnesses, do not make it contact the parts which will generate high heat. 
• Route wire harnesses to avoid sharp edges or corners. Avoid the projected ends of bolts and screws. 
• Route wire harnesses passing through the side of bolts and screws. Avoid the projected ends of bolts and screws.

G.B 15/03/25