Mustang Skid Steer Loader 2026 2041 Service Manual (917171) – PDF DOWNLOAD

Mustang Skid Steer Loader 2026 2041 Service Manual (917171) – PDF DOWNLOAD

TABLE OF CONTENTS:

Mustang Skid Steer Loader 2026 2041 Service Manual (917171) – PDF DOWNLOAD

Specifications Page 1-1
Specifications 1-1
Tire Options 1-1
Buckets and Capacities 1-1
General Specifications 1-2
Safety Page 2-1
General Information 2-1
Signal Words 2-1
Additional Safety Reminders 2-1
Mandatory Safety Shutdown Procedure 2-2
Liftarm Support Device 2-3
Liftarm Support Device Engagement 2-3
Liftarm Support Device Disengagement 2-4
Rollover Protective Structure (ROPS) – Raising 2-4
Rollover Protective Structure (ROPS) – Lowering 2-5
Relieving Hydraulic Pressure 2-6
Skid-Steer Loader Raising Procedure 2-6
Skid Loader Lowering Procedure 2-7
Lubrication Page 3-1
General Information 3-1
Hydraulic Oil Reservoir 3-1
Crankcase Oil 3-2
Hydraulic Oil Tank Drain Procedure 3-2
Chaincases 3-3
Chaincase Oil Change Procedure 3-3
Grease Fitting Locations 3-3
Cooling System Drain Procedure 3-4
PRINTED IN USA i 917171/AP0106
2026/2041 TABLE OF CONTENTS
Mainframe Page 4-1
Introduction 4-1
Engine Access Cover Removal and Installation 4-2
Rollover Protective Structure (ROPS) Removal and Installation 4-2
Seat Removal and Installation 4-4
Seat Slide Replacement 4-4
Rollover Protective Structure (ROPS) Rear Window Removal and Installation 4-5
Restraint Bar Removal and Installation 4-7
All-Tach™ Bracket Removal and Installation 4-9
Liftarm Removal and Installation 4-10
Liftarm Bushing Replacement 4-13
Liftarm Stop Installation and Adjustment 4-14
Floor Cover and Kick Plate Removal and Installation 4-16
Fuel Level Sender Removal and Installation 4-19
Rear Grille Removal and Installation 4-20
Wheel Drives Page 5-1
Introduction 5-1
Drive Chain Adjustment 5-2
Drive Chain Removal and Installation 5-3
Axle Removal and Installation 5-4
Controls Page 6-1
Introduction 6-1
Control Handle Removal and Installation 6-6
Control Handle Position and Tracking Adjustment 6-7
Dual Control Weldment Removal and Installation – T-Bar Controls 6-9
Neutral Centering Device and Pump Arm Removal and Installation 6-10
Neutral Centering Device Adjustment 6-11
Lift/Tilt Control Removal and Installation 6-12
Lift/Tilt Control Adjustment 6-13
Auxiliary Hydraulics Removal and Installation 6-14
Auxiliary Hydraulics Adjustment 6-15
Hand Throttle, Hand Throttle Cable and Throttle Rod Removal and Installation 6-16
Foot Throttle and Foot Throttle Cable Removal and Installation – T-Bar Controls 6-18
Hand Throttle Adjustment 6-19
Hand Throttle Tension Adjustment 6-20
Foot Throttle Adjustment – T-Bar Controls 6-21
917171/AP0106 ii PRINTED IN USA
TABLE OF CONTENTS 2026/2041
Hydrostatic System Page 7-1
Introduction 7-1
Troubleshooting Guide 7-3
Charge Pressure Test and Adjustment 7-7
Hydrostatic Pump Relief Valves 7-8
Drive Motor Hot Oil Shuttle Valve 7-8
Hydrostatic Pump Removal and Installation 7-9
Hydrostatic Pump Flexible Drive Plate Removal and Installation 7-11
Drive Motor Removal and Installation 7-12
Hydraulic System Page 8-1
Introduction 8-1
Troubleshooting Guide 8-3
System Pressure Test – Control Valve 8-7
Tilt Cylinder Test 8-9
Self-Leveling Valve Test 8-11
Self-Leveling Valve Adjustment 8-12
Lift Cylinder Test 8-13
Solenoid Valve Test 8-14
Hydraulic Oil Filter Element Replacement 8-16
Tilt Cylinder Removal and Installation 8-19
Lift Cylinder Removal and Installation 8-21
Lift and Tilt Cylinder Disassembly and Assembly 8-23
Gear Pump Removal and Installation 8-24
Self-Leveling Valve Removal and Installation 8-26
Safety Lock Valves – Removal and Installation 8-27
Lift, Tilt and Brake Safety Lock Valves – Disassembly and Assembly 8-29
Control Valve Removal and Installation 8-30
Hydraulic/Hydrostatic System Schematic 8-32
PRINTED IN USA iii 917171/AP0106
2026/2041 TABLE OF CONTENTS
All-Tach is a trademark of the Gehl Company
Electrical System Page 9-1
Description of Operation 9-1
Troubleshooting Guide 9-4
Relay Test and Operation 9-6
Electrical Circuits 9-8
Seat Switch Removal and Installation 9-15
Restraint Bar Switch Removal and Installation 9-16
Front and Rear Work Light Bulb Replacement 9-17
Electrical System Schematic 9-18
Engine Page 10-1
Introduction 10-1
Troubleshooting Guide 10-2
Engine Oil Filter Element Removal and Installation 10-4
Air Cleaner Assembly Removal and Installation 10-7
Air Filter Element Removal and Installation 10-7
Fuel Filter Removal and Installation 10-8
Water Separator Element Removal and Installation 10-8
Electric Fuel Pump Removal and Installation 10-9
Priming Diesel Fuel System 10-9
Battery Removal and Installation 10-10
Starter Removal and Installation 10-11
Exhaust Assembly Removal and Installation 10-11
Fan Belt Adjustment 10-12
Radiator/Cooler Removal and Installation 10-15
Fan Shroud Removal and Installation – 2041 Models 10-16
Fuel Tank Removal and Installation 10-17
Engine Removal and Installation 10-19
Index
917171/AP0106

DESCRIPTION:

Mustang Skid Steer Loader 2026 2041 Service Manual (917171) – PDF DOWNLOAD

INTRODUCTION

• With correct maintenance and proper use, Mustang skid-steer loaders will give years of dependable service. This service manual is intended to be a guide in the assembly and disassembly, installation and removal, adjustment and testing, troubleshooting and replacement of components that together make up the Mustang 2026/2041 family of skid-steer loaders.
• In many of the procedures found within, the installation steps are the exact opposite of the removal steps and vice versa, and therefore, the opposite procedure is not written. Instead, a note to reverse the procedure will be stated. This reduces redundancy and excessive pages in the manual. In cases though, where the assembly and disassembly or removal and installation procedures differ and additional steps or safety concerns are paramount, the entire reverse procedure will be written out to include the new information.
• The Table of Contents and Index can be used to make the procedure you need to find an easier process. Also, there are black tabs extending off the pages highlighting the chapters for those who prefer to thumb through the manual. Many schematics, photographs, and line art drawings are used to help perform the necessary repairs, tests, or adjustments that the 2026/2041 skid-steer loaders need to keep them in good running condition. If you have any additional questions, please contact your authorized Mustang dealer or call the Mustang Service Department for assistance. 
• IMAGES PREVIEW OF THE MANUAL: