Tadano Truck Crane TL-250E-3 Operation and Maintenance Manual -PDF DOWNLOAD

Tadano Truck Crane TL-250E-3 Operation and Maintenance Manual -PDF DOWNLOAD

FILE DETAILS:

Tadano Truck Crane TL-250E-3 Operation and Maintenance Manual -PDF DOWNLOAD

Language : English,FRENCH
Pages :269
Downloadable : Yes
File Type : PDF

TABLE OF CONTENTS:

Tadano Truck Crane TL-250E-3 Operation and Maintenance Manual -PDF DOWNLOAD

Safety A-1
Safety Rules A-3
Before Operation A-4
Rules for Operation (Setting Outriggers) !A-13 Rules for Operation (General)
A-15
Rules for Operation (Weather) A-32 Rules for Operation (Power Lines,
Radio Waves) A-35 Rules for Operation (Special Operation) A-37 After
Operation A-38
Rules for Road Travel A-39
Rules for inspection and Maintenance A-41
Warning Labels A-54
Warning Labels-Location and Contents A-55
Contents 1
Preface 5
Servicing and Ordering Parts 6
Components 7
Layout Of Controls 8
Crane Operator’ s Cab “8
Terminology 10
[ OPERATION]
Crane Operation Procedure-Summary15
Preparatory Steps 15
During Operation 17
At the End of Operation 18
How to Read Performance Data Plate 19
Working Radius / Lifting Height Chart 19 Total Rated Load Table
AML (Overload Prevention Device) 25 Configuration and Functions of the
AML System28
Controls 31
Names and Functions of the AML Main Unit Parts 32
Registering Operational Status 39
AML Pre-operational Inspection 43
How to Use the Working Range Restriction Function 46
Display Alteration 50
Recovery from an Automatic Stop 51
Display and Disposition of Failure Messages 53
Disposition of System Troubles 56
Other Safety Devices57
Overwind Cutout Device 57
Front Jack Overload Warning Device 59
Accumulator Low Pressure Warning Device 60Starting and Stopping the Engine 61
Controls 61
Pre-starting Checks 61
Starting the Engine 62
Stopping the Engine 64
Operating the PTO and Warming Up the Machine 65
Operating the PTO 65
Warming Up the Machine 66
Checks to Make during Warm-up 66
Outriggers 67
Setting the Crane 67
Controls 68
Extending the Outriggers 69
Level Adjustments73
Front Jack 75
Stowing the Outriggers76
Crane Operator’s Cab 78
Opening and Closing the Door 78
Adjusting Seat Position 79
Adjusting Length of Control Levers 80
Acceleration81
Controls 81
Hoisting83
Controls 83
Hoisting Up and Down 84
Free-fall operation87
Other Winch-related Controls and Devices 89
Telescoping the Boom 91
Controls 91
Extending and Retracting the Boom 91
Emergency Telescoping Procedure 95
Elevating the Boom 96
Controls 96
Raising and Lowering the Boom96
Swinging the Boom 98
Controls 98
Swinging the Boom 98
Taking Out and Stowing the Main Hook Block 101
Taking Out Main Hook Block101
Stowing Main Hook Block 103
Reeving Wire Rope 105
Standard Number of Parts of Line 105
Reeving Procedure 107Single Top 110
Components110
Single Top Lift 111
Mounting the Single Top 112
Stowing the Single Top 115
Jib 118
Components118
Jib lift 119
Mounting the Jib 120
Changing the Jib Offset Angle 128
Stowing the Jib 131
Equipment Inside the Cab 139
Heater(option) 139
Other Equipment Inside the Cab 141
Equipment Outside the Cab 145
Oil Cooler(option) 145
[ INSPECTION AND MAINTENANCE]
Inspection and Maintenance147
Pre-operational and Periodic Inspection 148
Greasing 153
Maintenance Table 154
Greasing Chart 155
Gear Oil 156
Maintenance Table 156
Winch Speed Reducer Oil Level Check 157
Winch Speed Reducer Oil Replacement157
Swing Speed Reducer Oil Replacement158
Hydraulic System159
Maintenance Table 160
Oil Level Check (Hydraulic Oil Tank) 161
Oil Replacement (Hydraulic Oil Tank) 161
Oil Level Check (Oil Reservoir) 163
Oil Replacement (Oil Reservoir) 163
Return Filter (Hydraulic Oil Tank)164
Return Filter (Inside Swing Table) 164
Air Breather (Hydraulic Oil Tank) 165
Line Filter (Winch Clutch Circuit) 165
Line Filter (Winch Brake Circuit) 165
Line Filter (Automatic Stop Circuit) 166
Swing System 167
Maintenance Table 167
Swing Brake Bleeding 167
Swing Bearing Mounting Bolt Check 168Winch System 169
Maintenance Table 169
Winch Brake for Wear Check 170
Winch Brake Adjustment 171
Brake Cylinder 1 Bleeding174
Brake Cylinder 2 Bleeding175
Winch Clutch Circuit Bleeding 177
Winch Clutch Adjustment 179
Accelerator System 181
Maintenance Table 181
Accelerator Circuit Bleeding 181
Electrical System 183
Maintenance Table 183
Fuses Replacement 183
Wire Ropes 185
Proper Handling of Wire Ropes 185
Wire Rope Replacement 187
[INFORMATION AND DATA]
Major Specifications 195
Crane Specifications 195
Overall Dimensions196
Weight 197
Relief Valve Pressure197
Wire Rope Specifications 198
Other 198
Oils and Greases 199
Oil and Grease Table 199
Recommended Oils and Greases 201
Consumable Parts 204
Filters 204
Fuses 204

IMAGES PREVIEW OF THE MANUAL: